P2271Generic code

P2271 Code: O2 Sensor Signal Stuck Rich (Bank 1 Sensor 2)

The P2271 code means the oxygen sensor on bank 1, behind the catalytic converter, stayed reading rich and did not react when the computer changed the mixture on purpose. It is usually a contaminated sensor, a signal wire shorted to voltage or a mixture that really is rich. Most of the time you will not notice any driving symptom, but it can keep you from passing an inspection.

Severity
Medium
Can I keep driving?
Yes, no immediate risk
Estimated cost
$50 to $250
Difficulty
Easy
System
Air and Fuel
Applies to
All OBD2 vehicles

Updated Reviewed by Renzo Chacca

On this page

What the P2271 code means

To check the sensor, the computer enriches or leans out the mixture for an instant and expects the signal to change. If the signal stays above about 0.7 V after that test, it stores the P2271 code. Bank 1 is the side of the engine that has cylinder number 1. On an inline engine there is only bank 1.

Sensor 1 is the one ahead of the catalytic converter, and it controls the mixture. Sensor 2 is behind the converter and monitors it.

A signal stuck rich can come from a contaminated sensor, from a signal wire shorted to voltage, or from a mixture that really is rich. On sensor 2, a hollowed-out catalytic converter or a leak in the flex pipe produces this behavior.

P2271 code symptoms

  • Check engine light on.
  • Usually no driving symptoms.
  • A catalytic converter code may be stored along with it.
  • It can keep the vehicle from passing an emissions inspection.

Likely causes of the P2271 code

  1. Aged or contaminated oxygen sensor. Oil, coolant or silicone additives are the usual contaminants.
  2. Exhaust leak near the sensor.
  3. Mixture that really is rich because of another fault. Check the fuel trims.
  4. Sensor wiring damaged by heat or shorted.

How to diagnose the P2271 code step by step

  1. Graph the sensor signal with the engine warm at 2,500 rpm.
  2. Force a mixture change by snapping the throttle open (rich) or letting off the pedal (lean). The sensor should respond within a few tenths of a second.
  3. Check the fuel trims to rule out a mixture that is really wrong.
  4. Look for exhaust leaks ahead of the sensor.
  5. Inspect the sensor. White or greenish deposits point to coolant or silicone contamination.

How to fix the P2271 code

  • Replace the sensor if it does not respond to mixture changes.
  • Repair any exhaust leaks.
  • Correct the cause of the wrong mixture if there is one.
  • Clear the codes and complete a drive cycle.

After the repair, watch the live signal once more. If the P2271 code stays away and the signal behaves normally again, the job is done.

Technical reference data

  • Zirconia sensor: swings between 0.1 and 0.9 V several times a second with the engine warm.
  • Response time of a healthy sensor: less than 100 ms going from lean to rich.
  • These are reference values only: check the manufacturer data for your vehicle.

Brand-specific notes

This code is common on several makes. The sensor age and any exhaust leaks are the first things to check.

P2271 on Ford

On Ford vehicles, P2195 and P2196 often appear after exhaust leaks or with sensors that have more than 150,000 km (about 93,000 miles) on them.

P2271 on Mazda

This code is frequent on Mazda vehicles. Start with the sensor and the exhaust next to it.

P2271 on Chevrolet

This code is frequent on Chevrolet vehicles. Start with the sensor and the exhaust next to it.

Frequently asked questions about P2271

Can I drive with a P2271 code?
Yes, in the short term. A poorly controlled mixture raises fuel use and can damage the catalytic converter.
Is it always the sensor?
No. An exhaust leak or a mixture that really is wrong produces the same code.
Why does a sensor get contaminated?
Oil consumption, coolant leaking through the head gasket, or silicone sealants that are not safe for sensors can all coat it.
How much does it cost to fix P2271?
Between $50 and $250. A new sensor is the usual repair, and an exhaust leak fix can land anywhere in that range.
What does the P2271 code mean?
It is a generic OBD2 code that means the bank 1 sensor 2 oxygen sensor, behind the catalytic converter, is stuck reading rich and did not react when the computer changed the mixture on purpose.
Will a P2271 code clear itself?
The light can go out after several drive cycles if the cause was temporary. A contaminated sensor or a shorted wire will bring the code back until it is fixed.
What is the most common cause of P2271?
An aged or contaminated oxygen sensor that no longer reacts. An exhaust leak or a worn catalytic converter near the sensor is the other usual suspect.

Related codes

Questions about the P2271 code

There are no questions about this code yet. Tell us about your case: vehicle, symptoms and what you have already checked.