P0619Generic code

P0619 Code: Alternative Fuel Control Module RAM/ROM Error

The P0619 code means the gas (alternative fuel) control module detected an internal memory error in its RAM or ROM. Check its power supply and grounds before you replace the computer. Reprogramming the module often clears the fault.

Severity
Medium
Can I keep driving?
Yes, but with caution
Estimated cost
$0 to $1,500
Difficulty
Hard
System
Computer and Outputs
Applies to
All OBD2 vehicles

Updated Reviewed by Renzo Chacca

On this page

What the P0619 code means

This code belongs to vehicles with an alternative fuel system, such as a CNG or propane conversion. The P0619 code is set when the module that manages that fuel runs its self-test and finds an error in its own memory. The problem is inside the module, so in many cases it can be solved by reprogramming it.

Before you condemn the computer, always check its power supply and grounds. Low voltage, a loose battery terminal or a corroded ground can cause internal errors that disappear as soon as the connection is fixed. It is also worth looking for manufacturer software updates, because many of these codes are cleared by reflashing the computer without replacing it.

If the computer does have to be replaced, keep in mind that it almost always needs to be programmed: VIN, immobilizer, option configuration and, on many vehicles, relearn procedures afterward. A used computer that has not been programmed can leave the vehicle unable to start.

P0619 code symptoms

  • Check engine light on.
  • The engine may not start or may run in limp mode.
  • Other codes stored at the same time in several systems.

Likely causes of the P0619 code

  1. Computer power supply or ground problem. Low voltage or a connection with resistance.
  2. Disconnected or discharged battery. This is especially true for P0603.
  3. Software with bugs. Manufacturer updates exist for many of them.
  4. Moisture or corrosion inside the computer. Worn case seals or water getting in through the engine bay are the usual reasons.
  5. Internal computer failure. Consider this only after everything above has been ruled out.

How to diagnose the P0619 code step by step

  1. Clear the code and see whether it comes back. Some are caused by a one-time event, such as a discharged battery.
  2. Measure the voltage at the computer power pins and compare it with the battery voltage.
  3. Measure the voltage drop across the grounds. It should be under 0.1 volts under load.
  4. Look for technical service bulletins and software updates for your vehicle.
  5. Inspect the computer connector for moisture, corrosion or bent pins.

How to fix the P0619 code

  • Correct the power supply and ground problems.
  • Reprogram or update the computer.
  • Replace the computer only if everything above checks out, and program it for the vehicle.
  • Clear the codes and verify the repair.

Technical reference data

  • Supply voltage: battery voltage, with less than 0.2 volts of drop.
  • Programming needs stable voltage, so connect a battery maintainer first.
  • Reference values: check the manufacturer data for your vehicle.

Brand-specific notes

Manufacturers publish software updates that fix many of these internal computer codes. Ask the dealer before you buy a replacement computer.

P0619 on Ford

Ford has released updates for similar internal computer codes such as P0606. Ask the dealer whether one applies to your vehicle.

P0619 on Chrysler

Chrysler has also published updates for similar internal computer codes such as P0606. Check with the dealer before replacing the module.

P0619 on Hyundai

Hyundai is another brand that has released updates for similar internal computer codes such as P0606. Check with the dealer before replacing the module.

Frequently asked questions about P0619

What does the P0619 code mean?
It is a generic OBD2 code that means the alternative fuel control module found an error in its own RAM or ROM memory. The fault is internal to the module, but power, ground and software problems can cause it.
Can I drive with a P0619 code?
With caution. It depends on the symptoms: if the engine runs normally you can drive carefully to a shop, but if it goes into limp mode, have the vehicle taken to a mechanic.
Does the computer have to be replaced?
Not always. Many times the cause is the power supply, a ground or the software, and reprogramming the module solves it.
Can I use a used computer?
Only if it is programmed correctly for your vehicle. An unprogrammed used unit can leave the engine unable to start.
How much does it cost to fix P0619?
It can cost $0 if the cause was just the battery or a loose ground. If the computer has to be replaced and programmed, the cost can reach $1,500.
Will a P0619 code clear itself?
Sometimes. If the error came from a one-time event such as a discharged battery, the P0619 code may not return after you clear it. If it does come back, the cause is still there.

Related codes

Questions about the P0619 code

There are no questions about this code yet. Tell us about your case: vehicle, symptoms and what you have already checked.