U0427Generic code

U0427 Code: Invalid Data Received From Vehicle Security Control Module

The U0427 code means the vehicle security module is sending messages, but with data that does not make sense or is out of range. The alarm or the starting system may fail as a result. The module is often just passing along a bad reading from one of its own sensors.

Severity
Medium
Can I keep driving?
Yes, but with caution
Estimated cost
$0 to $1,200
Difficulty
Hard
System
Communication Network
Applies to
All OBD2 vehicles

Updated Reviewed by Renzo Chacca

On this page

What the U0427 code means

Unlike a loss of communication, here the messages from the vehicle security module do arrive, but their content is not valid: impossible values, counters that do not advance or incompatible data. The module that receives that data stores the U0427 code and stops using it.

The usual causes are a sensor connected to the vehicle security module that gives wrong readings (the module forwards the bad data), incompatible software after a module was replaced or reprogrammed, an incorrect configuration, or an internal failure. Check the codes stored in the vehicle security module itself first: they usually point to the origin.

After a module is replaced, it often has to be configured (coded) so that it sends data in the format the other modules expect. Skipping that step is a common reason the code appears right after a repair.

U0427 code symptoms

  • Warning lights on.
  • The alarm or the starting system may fail.
  • Codes stored in the sending module.

Likely causes of the U0427 code

  1. Codes stored in the vehicle security module itself. One of its sensors is giving wrong readings.
  2. Incompatible software or configuration. This follows a module that was replaced or reprogrammed.
  3. Unstable supply voltage. Modules send wrong data when they reset.
  4. Internal failure of the vehicle security module. Only after sensors, software and power have been ruled out.

How to diagnose the U0427 code step by step

  1. Read the codes in the vehicle security module and solve those first.
  2. Check for recent replacements or reprogramming.
  3. Verify the module configuration with a compatible scan tool.
  4. Measure the battery voltage.

How to fix the U0427 code

  • Resolve the codes in the sending module.
  • Configure or update the module software.
  • Replace the module if it has an internal failure.
  • Clear the codes in all modules.

Technical reference data

  • Invalid data includes out-of-range values, message counters and incorrect checksums.
  • These are reference values: check the manufacturer data for your vehicle.

Brand-specific notes

After the repair, clear the codes in every module and confirm the U0427 code stays gone. Many modules keep old U codes from when the fault was present. Accessories installed later (alarms, GPS trackers, OBD2 adapters left plugged in permanently) are a frequent cause of network problems.

Frequently asked questions about U0427

What does the U0427 code mean?
It means the vehicle security module is sending data that another module considers invalid, such as impossible values or counters that do not advance. The receiving module stored the code and stopped using that data.
Can I drive with a U0427 code?
With caution, depending on the system affected. The alarm or the starting system may fail, so if the vehicle starts normally you can drive, but have it checked soon in case it stops starting.
Is the vehicle security module bad?
Not necessarily. Often it is only forwarding a wrong reading from one of its sensors, so read its own codes before you replace anything.
What is coding?
It is the configuration that adapts a module to the equipment on the vehicle. A replacement module often needs it before it sends data in the expected format.
How much does it cost to fix U0427?
Between $0 and $1,200. Clearing a sensor fault or recoding can be cheap, while replacing and programming a module is at the top of the range.
Will a U0427 code clear itself?
Only if the cause was temporary, such as a voltage dip. If the bad data is still being sent, the code will return after you clear it.
What is the most common cause of U0427?
A faulty sensor on the vehicle security module, or software and configuration that do not match after a module was replaced or reprogrammed.

Related codes

Questions about the U0427 code

There are no questions about this code yet. Tell us about your case: vehicle, symptoms and what you have already checked.