U0202Generic code

U0202 Code: Lost Communication With Door Control Module D

The U0202 code means other modules in the vehicle stopped receiving messages from door control module D. The usual effect is that the power window or the lock of that door does not work. The cause is often power, ground, a connector or a weak battery rather than the door module itself.

Severity
Low
Can I keep driving?
Yes, no immediate risk
Estimated cost
$0 to $1,500
Difficulty
Medium
System
Communication Network
Applies to
All OBD2 vehicles

Updated Reviewed by Renzo Chacca

On this page

What the U0202 code means

The modules in your vehicle trade information constantly over a data network, normally a CAN bus. Door control module D runs the power window, the lock and the mirror of a rear door. When the other modules stop receiving its messages for a certain length of time, they store the U0202 code.

Keep in mind that the code is stored by the module that misses the information, not by the one that is failing. That is why it often shows up in several modules at once. The problem can be in door control module D (no power, no ground or an internal failure), in its connector, or in the network wiring that runs to it.

Typical location: inside the door panel. If that area is exposed to water or was repaired recently, start there.

The diagnostic method, in order: 1) battery and alternator (low voltage is the number one cause of bursts of U codes); 2) the module list on the scan tool, to see which module does not respond; 3) power, fuses and grounds of the module that does not respond; 4) network resistance at the OBD2 connector (about 60 ohms between pins 6 and 14 with the battery disconnected); 5) connectors and wiring at the module, especially in damp areas (under carpets, in doors, in the trunk).

Measuring the CAN network step by step is what separates a quick fix from a week of swapped parts, so follow that order before you buy anything.

U0202 code symptoms

  • Warning lights on in the dashboard.
  • The power window or the lock of that door does not work.
  • Communication codes in several modules at the same time.
  • The fault can come and go (for example, with rain or over bumps).

Likely causes of the U0202 code

  1. Power or ground to the module. A blown fuse, a corroded ground or a loose power connector.
  2. Weak battery or low voltage. The modules reset and lose communication.
  3. Module connector with water or corrosion. Very common on modules mounted in damp areas, and a door is one of them.
  4. Damaged network wiring. CAN high or CAN low cut or shorted.
  5. Failed door control module D. Only after everything above has been ruled out.
  6. Poorly installed accessory. Alarms or trackers wired into the network.

How to diagnose the U0202 code step by step

  1. Measure the battery voltage at rest (12.4 to 12.7 V) and with the engine running (13.5 to 14.7 V).
  2. Check on the scan tool which modules respond. If door control module D does not show up, the fault is in it or in its connection.
  3. Check the fuses and grounds of the module against the wiring diagram.
  4. Measure the network at the OBD2 connector. About 60 ohms between pins 6 and 14 with the battery disconnected, and roughly 2.5 V on each line with the key on.
  5. Inspect the module connector for moisture, corrosion and bent pins.
  6. Measure CAN high and CAN low at the module connector. They should have continuity back to the OBD2 connector.

How to fix the U0202 code

  • Repair the power, the ground or the connector of the module.
  • Repair the network wiring.
  • Replace and program the module if it has failed (it almost always needs programming).
  • Clear the codes in all modules and verify the repair.

Technical reference data

  • CAN network resistance between OBD2 pins 6 and 14: about 60 ohms.
  • CAN high: 2.5 to 3.5 V. CAN low: 1.5 to 2.5 V.
  • These are reference values: check the manufacturer data for your vehicle.

Brand-specific notes

After the repair, clear the codes in every module and confirm the U0202 code stays gone. Many of them keep old U codes from when the fault was present. Accessories installed later (alarms, GPS trackers, OBD2 adapters left plugged in permanently) are a frequent cause of network problems.

Frequently asked questions about U0202

What does the U0202 code mean?
It means other modules stopped receiving messages from door control module D over the vehicle data network. The code points to a communication loss, not necessarily a dead module.
Can I drive with a U0202 code?
In general, yes. The severity is low, and the main effect is that the functions of that module may not be available, so the window or lock of that door may not work.
Does U0202 mean door control module D is bad?
Not necessarily. The most common causes are its power, its ground, its connector or the battery. Replace the module only after those are ruled out.
Why do so many codes show up at once?
Because every module that expected information from the affected module records the fault. One silent module can leave codes all over the network.
How much does it cost to fix U0202?
Anywhere from $0, if it was the battery or a fuse, up to $1,500 if the module has to be replaced and programmed.
Will a U0202 code clear itself?
If the cause was a temporary voltage drop, the U0202 code may not come back after you clear it. If it returns, the fault is still present and needs to be found.
What is the most common cause of U0202?
Power or ground problems at the module, followed by a weak battery and a wet or corroded connector. The door module itself is the last thing to suspect.

Related codes

Questions about the U0202 code

There are no questions about this code yet. Tell us about your case: vehicle, symptoms and what you have already checked.