U0183Generic code

U0183 Code: Lost Communication With Lighting Control Module Rear

The U0183 code means other modules in the vehicle stopped receiving messages from the rear lighting control module. The tail lights or brake lights can misbehave. Start with the battery, the module power and grounds, and the network wiring before you replace anything.

Severity
Medium
Can I keep driving?
Yes, no immediate risk
Estimated cost
$0 to $1,500
Difficulty
Medium
System
Communication Network
Applies to
All OBD2 vehicles

Updated Reviewed by Renzo Chacca

On this page

What the U0183 code means

The modules in your vehicle constantly exchange information over a data network, normally CAN. The rear lighting control module controls the tail lights, brake lights and rear turn signals. When the other modules stop receiving its messages for a set amount of time, they store the U0183 code.

The code is stored by the module that is missing the information, not by the module that is failing. That is why it often shows up in several modules at once. The problem can be in the rear lighting module itself (no power, no ground or an internal failure), in its connector, or in the network wiring that runs to it.

Typical location: in the trunk. If that area is exposed to water or was worked on recently, start there.

Diagnostic order: 1) battery and alternator (low voltage is the number one cause of bursts of U codes); 2) the module list in the scan tool, to see which module is not responding; 3) power, fuses and grounds of the module that is not responding; 4) network resistance at the OBD2 connector (about 60 ohms between pins 6 and 14 with the battery disconnected); 5) module connectors and wiring, especially in damp areas (under carpets, in doors, in the trunk).

The CAN Network and U Codes guide explains in detail how to measure the network and isolate the module that is bringing it down.

U0183 code symptoms

  • Warning lights on in the dash.
  • Problems with the tail lights or brake lights.
  • Communication codes stored in several modules at the same time.
  • The fault can be intermittent (for example, in rain or over bumps).

Likely causes of the U0183 code

  1. Module power or ground. A blown fuse, a corroded ground or a loose power connector.
  2. Weak battery or low voltage. Modules reset and lose communication.
  3. Module connector with water or corrosion. Very common on modules mounted in damp areas, such as the trunk.
  4. Damaged network wiring. A CAN high or CAN low wire that is cut or shorted.
  5. Failure of the rear lighting module. Only after everything above has been ruled out.
  6. Poorly installed accessory. Alarms or trackers wired into the network.

How to diagnose the U0183 code step by step

  1. Measure the battery voltage at rest (12.4 to 12.7 V) and with the engine running (13.5 to 14.7 V).
  2. Check in the scan tool which modules respond. If the rear lighting module does not show up, the fault is in it or in its connection.
  3. Check the module fuses and grounds using the wiring diagram.
  4. Measure the network at the OBD2 connector. About 60 ohms between pins 6 and 14 with the battery disconnected, and roughly 2.5 V on each line with the key on.
  5. Inspect the module connector for moisture, corrosion and bent pins.
  6. Measure CAN high and CAN low at the module connector. They should have continuity back to the OBD2 connector.

How to fix the U0183 code

  • Repair the module power, ground or connector.
  • Repair the network wiring.
  • Replace and program the module if it has failed (it almost always needs programming).
  • Clear the codes in all modules and verify the repair.

Technical reference data

  • CAN network resistance between OBD2 pins 6 and 14: about 60 ohms.
  • CAN high: 2.5 to 3.5 V. CAN low: 1.5 to 2.5 V.
  • These are reference values only: check the manufacturer data for your vehicle.

Brand-specific notes

After the repair, clear the codes in every module. Many of them keep old U codes from the time the fault was present, and those can leave a warning light on or confuse the next scan.

Accessories installed after purchase (alarms, GPS trackers and OBD2 adapters left plugged in all the time) are a frequent cause of network problems, so unplug them first when you chase a U0183 code.

Frequently asked questions about U0183

Can I drive with a U0183 code?
In general, yes, but check that your tail lights and brake lights work before you go. Working brake lights are essential so that drivers behind you know when you stop.
Does U0183 mean the rear lighting module is bad?
Not necessarily. The most frequent causes are its power supply, its ground, its connector or the battery, and the module itself is replaced last.
Why are so many codes showing at once?
Every module that was waiting for information from the affected module stores its own fault. One problem on the network can therefore produce a long list of codes.
How much does it cost to fix U0183?
From $0, if it was only the battery or a fuse, up to about $1,500 if the module has to be replaced and programmed.
What does the U0183 code mean?
It is a generic OBD2 network code that means the vehicle lost communication with the rear lighting control module. It points to a power, ground, connector or wiring problem as often as to the module itself.
Will a U0183 code clear itself?
If the cause was a brief voltage dip, the code may stop returning after the fault goes away, but the stored code stays until it is cleared. A loose connector or a damaged wire will bring it back.
What is the most common cause of U0183?
Low battery voltage and problems with the module power, ground or connector are the most common causes. Check those before you suspect the module.

Related codes

Questions about the U0183 code

There are no questions about this code yet. Tell us about your case: vehicle, symptoms and what you have already checked.