P2008Generic code

P2008 Code: Intake Manifold Runner Control Circuit/Open (Bank 1)

The P2008 code means an open circuit in the intake manifold runner control valves on bank 1: the component gets no current when it is activated. It can cause a loss of torque at low rpm and a slightly rough idle. The engine runs, with a little less performance.

Severity
Low
Can I keep driving?
Yes, no immediate risk
Estimated cost
$40 to $450
Difficulty
Medium
System
Air and Fuel
Applies to
All OBD2 vehicles

Common in: Ford, Volkswagen

Updated Reviewed by Renzo Chacca

On this page

What the P2008 code means

Many engines have flaps or valves in the intake manifold (IMRC, Intake Manifold Runner Control, also called swirl or tumble flaps) that change the length or shape of the intake runner. At low rpm they close so the air enters faster and with more turbulence, which improves torque and combustion. At high rpm they open to let more air through. An electric motor or a vacuum actuator controlled by a solenoid moves them, and a position sensor tells the computer whether they really moved.

The computer watches the control circuit from its own driver transistor. The P2008 code means an open circuit: the component gets no current when it is activated. Before you replace the component, check the fuse, the relay, the connector and the wiring, because they are the most common cause.

The computer does the commanding on an electric actuator or on the solenoid that supplies vacuum to the pneumatic actuator. Bank 1 is the side of the engine where cylinder number 1 is. Inline engines only have bank 1. On V engines, bank 2 is the opposite side.

Measure the resistance of the component at its connector. If it is infinite, the component is open inside. If it is correct, follow the control wire back to the computer looking for a break, especially in the sections near the exhaust or at intermediate connectors.

P2008 code symptoms

  • Check engine light or another warning light on.
  • Loss of torque at low rpm and a slightly uneven idle.

Likely causes of the P2008 code

  1. Connector unplugged or with a broken lock.
  2. Open coil. The resistance reads infinite.
  3. Wire cut. Check the areas where it rubs.
  4. Blown fuse, often from an earlier short circuit.

How to diagnose the P2008 code step by step

  1. Activate the component with the scan tool and check whether it responds.
  2. Check the fuse and the relay. Measure voltage on both sides of the fuse, and swap the relay with an identical one.
  3. Measure the supply at the connector. You should see battery voltage with the key on or when it is activated.
  4. Measure the resistance of the component and compare it with the manual. Check the insulation to ground too.
  5. Check the control wire. Look for continuity all the way to the computer and for any short circuit.

How to fix the P2008 code

  • Repair the connector, the wiring or the power supply.
  • Replace the intake manifold runner control valves if they do not respond with correct power and control.
  • Clear the codes and verify.

Technical reference data

  • Vacuum actuator: it should hold about 15 to 20 inHg without losing vacuum for one minute.
  • Electric actuator: 12 volt supply, with control by a PWM signal or by reversing polarity.
  • Position sensor: 5 volt reference and a signal of roughly 0.5 to 4.5 volts depending on the flap position.
  • These values are only a guide, so look up the manufacturer data for your vehicle.

Brand-specific notes

On some diesels the flaps fill up with carbon and can break. A fragment inside the cylinder can cause a serious failure, so some shops remove the flaps following manufacturer procedures.

P2008 on Ford and Mazda

This code is frequent on Ford Duratec and Mazda MZR gasoline engines.

P2008 on Volkswagen, BMW, Mercedes-Benz and Fiat

It is also frequent on the diesel engines with swirl flaps from Volkswagen, BMW, Mercedes-Benz and Fiat.

P2008 on GM V6 Engines

Several GM V6 engines are also known for this code.

Frequently asked questions about P2008

Can I drive with a P2008 code?
Yes. The engine runs, with a little less performance.
What do the intake manifold runner control valves do?
They are flaps in the intake manifold (IMRC, also called swirl or tumble flaps) that change the length or shape of the runner. At low rpm they close so the air enters faster and with more turbulence, which improves torque and combustion. At high rpm they open to let more air through.
Does the part always have to be replaced?
No. Check the fuses, relays, connectors and wiring first.
How much does it cost to fix P2008?
Roughly $40 to $450.
What does the P2008 code mean?
It is a generic OBD2 code that means the control circuit of the bank 1 intake manifold runner control valves is open. The computer sends the command but no current reaches the component.
Will a P2008 code clear itself?
Only if the cause was a passing glitch, such as a connector that was briefly loose. A cut wire, a blown fuse or an open coil will bring the P2008 code back.
What is the most common cause of P2008?
A connector that is unplugged or has a broken lock, or a cut wire in an area where it rubs. A blown fuse is common too, so check for the short circuit that blew it.

Related codes

Questions about the P2008 code

There are no questions about this code yet. Tell us about your case: vehicle, symptoms and what you have already checked.