P0662Generic code

P0662 Code: Intake Manifold Tuning Valve Control Circuit High (Bank 1)

The P0662 code means the computer sees high voltage in the bank 1 variable intake valve control circuit, from an open circuit or a short to voltage. It can cause a loss of torque at certain engine speeds. Check the connector and wiring first.

Severity
Low
Can I keep driving?
Yes, no immediate risk
Estimated cost
$40 to $600
Difficulty
Medium
System
Air and Fuel
Applies to
All OBD2 vehicles

Updated Reviewed by Renzo Chacca

On this page

What the P0662 code means

Many engines have an intake manifold with runners of variable length, or a valve that changes the shape of the air entering the cylinders (IMRC, IMTV, swirl). The computer moves it according to engine speed to gain torque down low and power up high.

The computer watches the control circuit from its own driver transistor. The P0662 code flags high voltage in that control circuit, either an open circuit or a short to voltage. Before you replace the component, check the fuse, relay, connector and wiring, which are the most common causes.

If the circuit fails, the valve stays in a fixed position. The engine loses some power at low or high rpm, but it still runs. The plastic rods and bushings in these valves break often.

To confirm the fault, measure the continuity of each wire between the component connector and the computer connector with the key off. It should be under 1 ohm, and an infinite reading means the wire is open. If the wiring is good, measure the component itself: infinite resistance confirms it is open inside.

P0662 code symptoms

  • Check engine light or another warning light on.
  • Loss of torque at certain rpm.
  • Less power at low or high rpm.
  • A rattling noise at the manifold (broken linkage).

Likely causes of the P0662 code

  1. Loose or broken connector. The most frequent cause, especially after another repair.
  2. Open coil or motor. Infinite resistance.
  3. Control wire cut between the component and the computer.
  4. Short to 12 volts. The control wire touches another wire that carries voltage.

How to diagnose the P0662 code step by step

  1. Activate the component with the scan tool and check whether it responds.
  2. Check the fuse and relay. Measure the voltage on both sides of the fuse, and swap the relay with an identical one.
  3. Measure the supply at the connector. You should see battery voltage with the key on or when the component is activated.
  4. Measure the resistance of the component and compare it with the manual. Also check the insulation to ground.
  5. Check the control wire for continuity to the computer and for shorts.
  6. Check the valve movement with the scan tool or a vacuum pump.

How to fix the P0662 code

  • Repair the connector, the wiring or the power supply.
  • Replace the bank 1 variable intake valve if it does not respond even with correct power and command signals.
  • Clear the codes and verify the repair.

Technical reference data

  • Electric or vacuum actuator with a 12 volt solenoid.
  • Reference values: check the manufacturer data for your vehicle.

Brand-specific notes

This code is very frequent on several makes, and the plastic linkage is worth checking on all of them.

P0662 on Ford

Very frequent on Ford, where the system is the IMRC.

P0662 on Mazda

Very frequent on Mazda.

P0662 on Volkswagen

Very frequent on Volkswagen.

P0662 on BMW

Very frequent on BMW, where the system is called DISA.

Frequently asked questions about P0662

Can I drive with a P0662 code?
Yes, with caution. The engine runs, but it may lose some power at low or high rpm because the valve is stuck in one position.
What does the variable intake valve do?
It changes the length or shape of the intake runners. The computer moves it with engine speed to gain torque at low rpm and power at high rpm.
Do I always have to replace the part?
No. Check the fuses, relays, connectors and wiring first, because they are the most common cause.
How much does it cost to fix P0662?
As a rough guide, between $40 and $600. A connector or wiring repair is at the low end, and a new valve is at the high end.
What does the P0662 code mean?
It is a generic OBD2 code that means the computer sees high voltage in the bank 1 intake manifold tuning valve control circuit.
What is the most common cause of P0662?
A loose or broken connector, especially after another repair was done nearby. A P0662 code can also come from an open coil or a cut control wire.

Related codes

Questions about the P0662 code

There are no questions about this code yet. Tell us about your case: vehicle, symptoms and what you have already checked.