P0182Generic code

P0182 Code: Fuel Temperature Sensor A Circuit Low

The P0182 code means the fuel temperature sensor signal is below its minimum value. On a thermistor that means the computer reads an impossibly high temperature, almost always from a short to ground. Look for a rubbed wire or a shorted sensor.

Severity
Low
Can I keep driving?
Yes, no immediate risk
Estimated cost
$40 to $300
Difficulty
Medium
System
Fuel Injection
Applies to
All OBD2 vehicles

Updated Reviewed by Renzo Chacca

On this page

What the P0182 code means

Fuel temperature sensor A is located on the fuel rail, in the fuel feed line or inside the fuel pump module, depending on the vehicle (very common on diesels and flex fuel vehicles). The computer uses it because fuel density changes with temperature, so it corrects the amount of fuel injected, and on flex fuel and diesel engines it also helps protect the system from overheating.

The sensor is an NTC thermistor: its resistance drops as the temperature rises. The computer sends it 5 V and reads the voltage that comes back. A signal below the minimum (normally less than 0.1 to 0.2 V) is the same as an impossibly high temperature, and that almost always means a short to ground: the signal wire touches metal or the sensor is shorted inside. While the fault lasts, the computer believes the fuel is very hot and adjusts injection for lower density. On diesels it may limit power. That is what sets the P0182 code.

Keep in mind that the code points to the circuit where the computer saw the problem, not necessarily the part that failed. Check the wiring before you replace the sensor, and treat the P0182 code as a starting point for testing rather than a parts list.

P0182 code symptoms

  • Check engine light on and steady.
  • The computer thinks the fuel is very hot and adjusts injection for lower density. On diesels it may limit power.
  • In many cases you notice nothing while driving, only the light on the dash.
  • Possible companion codes from the same sensor (low, high or intermittent signal).

Likely causes of the P0182 code

  1. Signal wire shorted to ground by rubbing against the engine or chassis. This is very common where the harness passes close to metal brackets.
  2. Internal short in the sensor, with its resistance dropping to almost zero ohms.
  3. Connector with water or corrosion that creates a path between pins.
  4. Also check: On flex fuel vehicles, the fuel composition sensor often measures temperature as well, so its P0176 to P0179 codes can show up alongside this one.

How to diagnose the P0182 code step by step

  1. Read the live data from the sensor and compare it with what you expect. After the vehicle has sat for several hours, the fuel temperature should be close to the ambient air temperature.
  2. Inspect the connector. Unplug it, look for green, backed-out or oily pins, and plug it back in firmly.
  3. With the key on and the sensor unplugged, measure the reference at the connector. You should see about 5 V between the signal pin and ground.
  4. Do the jumper test. With the sensor unplugged, the scan tool should show about -40 °C (-40 °F). When you join the two connector pins with a jumper wire, the reading should jump to over 120 °C (248 °F). If it does, the wiring is good and the problem is the sensor.
  5. Measure the sensor resistance and compare it with the technical data table at the current temperature.
  6. Do a wiggle test. With the engine running, move the harness and the connector while you watch the live data. A sudden jump gives away the spot where the fault is.
  7. Check the continuity of each wire between the sensor connector and the computer connector with the key off.

How to fix the P0182 code

  • Find where the wire rubs against ground and repair the insulation.
  • If the code changes to a high signal when you unplug the sensor, the sensor is shorted. Replace it.
  • Dry and clean the connector if it had water in it.
  • Use a quality OE or equivalent sensor. Cheap generic ones often have different response curves.
  • Clear the codes, drive a full drive cycle and check in the live data that the reading makes sense.

Technical reference data

  • Two-wire NTC thermistor with a 5 V reference.
  • Approximate resistance: 2,000 to 3,000 ohms at 20 °C (68 °F). It drops as the sensor warms up.
  • Open circuit: a reading of about -40 °C (-40 °F). Short circuit: over 120 °C (248 °F).
  • These are approximate values. Check the manufacturer data for your engine.

Brand-specific notes

The fuel temperature signal does not come from the same place on every vehicle. Where the sensor sits depends on the brand and on the type of engine.

P0182 on GM

On flex fuel GM vehicles, the fuel temperature is supplied by the fuel composition sensor itself.

P0182 on Ford

On common rail diesels, the fuel temperature sensor is usually on the high pressure pump or in the return line.

P0182 on Nissan

On common rail diesels, the fuel temperature sensor is usually on the high pressure pump or in the return line.

P0182 on Toyota

On common rail diesels, the fuel temperature sensor is usually on the high pressure pump or in the return line.

Frequently asked questions about P0182

What does the P0182 code mean?
The P0182 code means the fuel temperature sensor signal is below its minimum value. On a thermistor that is the same as an impossibly high temperature, and it almost always comes from a short to ground.
Can I drive with a P0182 code?
Yes, in general there is no immediate risk. The engine runs on a substitute value and may use a bit more fuel, so get it repaired soon.
What is the most common cause of P0182?
The most common cause is a signal wire rubbing against the engine or chassis and shorting to ground. A shorted sensor or a connector with water or corrosion is next on the list.
Does the P0182 code always mean I need a new fuel temperature sensor?
No. In most cases the fault is in the connector or the wiring. Do the supply, ground and continuity tests first, and replace the sensor only when those pass.
What is the difference between a low signal and a high signal?
On a thermistor, a low signal means an impossibly high temperature (a short), and a high signal means an impossibly low temperature (an open circuit).
How much does it cost to fix P0182?
Roughly $40 to $300. The cheap end is repairing a connector, and the expensive end is replacing the sensor with labor. Prices vary by region and shop.
Will a P0182 code clear itself?
Not on its own. If the cause was a loose connector that you have fixed, the code will not come back, but if the fault is still there the computer sets P0182 again. Clearing it with a scan tool without finding the cause only hides it for a while.

Related codes

Questions about the P0182 code

There are no questions about this code yet. Tell us about your case: vehicle, symptoms and what you have already checked.